The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Kajigul Nijinn
Country: Sri Lanka
Language: English (Spanish)
Genre: Love
Published (Last): 19 September 2017
Pages: 158
PDF File Size: 15.76 Mb
ePub File Size: 3.20 Mb
ISBN: 336-8-58243-132-7
Downloads: 51866
Price: Free* [*Free Regsitration Required]
Uploader: Kazilkis

We should set the bits in same pattern on Encoder and Decoder IC to xatasheet them. If you want security you can connect any of the 8 pins to 5V to make it high. Connected to the Ground of circuit.

Virgin Galactic — Commercial Space Flight. Arduino based GPS receiver. The Encoded 12 bit output data can be obtained from datashest pin. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

These two ICs together form an Encoder and Decoder pair. Choosing Battery for Robots. HT12E has a transmission enable pin which is on low. Transmission enable; active low. SPI Module of Arduino. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

This pin has to be connected to Ground 0V to enable the Transmission. It is mainly used in interfacing RF and infrared circuits.


HT12E Encoder IC

The IC has a built on oscillator. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. You can know to set up the HT12D after this from here. TL — Programmable Reference Voltage. This oscillator can be used by connecting these two pins through a 1M Resistor.

The encoded bit can be obtained from the Dout pin pin Submitted by admin on 30 October Interface GPS with Arduino. In the above circuit I have set the 8-bit address data as 0b, by darasheet all address pins to ground.

Choosing Motor For Robots. In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. I voltage; 5V 2. Skip to main content. HT12E is an encoder integrated circuit of 2 12 series of encoders.

This cycle is repeated as long as TE is kept low. Simply put, HT12E converts the parallel inputs into serial output. These are the 8-bit address bits, which is used to protect your data. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. As soon as TE returns to high, the encoder output completes its final cycle and then stops. They are paired with 2 12 series of decoders for use in remote control system applications. They can also be connected to switches to dagasheet send and receive data.


So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. What is Web Browser. It is ht122e important that your Decoder should also have this same address for them to htt12e to each other.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. The primary function of HT12E is to encode a bit and send it out through the output pin. Pull the Transmission Enable pin pin 14 to ground to activate transmission.

These 12 bits are divided into 8 address bits and 4 data bits. This high-density System-in-Package SiP integrates controller, power switches, and support components. Interface SD Card with Arduino. The IC is has a wide range of operating voltage from 2. Can range from 2.